The 18GHz SMA to N RF coaxial cable assembly is a flexible, 50-ohm microwave interconnect cable built for precision signal transmission between RF test instruments, antennas and microwave components. It pairs an SMA male connector on one end with an N-type male connector on the other, on a low-loss coaxial cable rated to 18 GHz with connectors fitted (34 GHz on the bare cable), making it suitable for RF laboratories, telecommunications test benches, antenna ranges and field survey equipment that mixes SMA and N-type interfaces.
Why Choose This SMA to N Coaxial Cable Assembly?
Mixed-connector RF setups are common wherever compact test gear (SMA) needs to connect to antennas, base stations or ruggedised equipment (N-type). Rather than stacking adapters – which add loss, reflections and failure points – this cable assembly runs a single continuous 50-ohm coaxial line between the two connector types, preserving signal integrity across the full frequency range.
Key Advantages
- Rated for signal transmission up to 18 GHz with connectors fitted
- Stable 50-ohm impedance for consistent RF performance
- Low insertion loss with >90dB screening effectiveness for strong EMI/RFI shielding
- Handles up to 1500V DC dielectric withstanding voltage
- Minimal phase change vs. bending (±0.3°/GHz) for repeatable measurements
- Flexible design with a 1.575in (40mm) repeated bend radius
- Wide -55°C to +125°C operating temperature range for lab, field and outdoor use
- Available in 10 standard lengths from 0.1m to 5m
Key Features of the SMA to N RF Cable Assembly
1. High-Frequency Performance to 18 GHz
Built on a double-shielded 50-ohm coaxial core, this RF coaxial cable assembly maintains stable electrical characteristics across its full operating range. It supports demanding microwave and RF applications including vector network analysis, spectrum analysis, signal generation and antenna calibration, where connector loss and reflections directly affect measurement accuracy.
2. Dual-Shielded, Low-Loss Construction
The cable uses a silver-plated copper inner conductor over solid PTFE insulation, with a silver-plated copper strip inner shield and a silver-plated copper wire outer shield beneath a durable FEP outer jacket. This layered shielding delivers screening effectiveness greater than 90dB, keeping external interference out and RF signal loss to a minimum.
3. SMA Male to N Male Connector Configuration
The SMA male connector suits compact RF test equipment, portable analysers and PCB-mounted RF modules, while the N-type male connector is the standard interface for antennas, base station hardware, GNSS/GPS receivers and ruggedised outdoor equipment. This assembly bridges the two interfaces in a single low-loss run, removing the need for a separate SMA-to-N adapter.
4. Flexible, Field-Ready Cable Jacket
A durable, flexible outer jacket allows the cable to be routed through tight equipment racks, antenna masts and survey poles without kinking, while the 40mm repeated bend radius and low phase-vs-bending specification keep RF performance consistent even after repeated flexing.
5. Multiple Cable Lengths for Flexible Setups
This cable assembly is available in 10 standard lengths – 0.1m, 0.15m, 0.2m, 0.3m, 0.5m, 1m, 1.5m, 2m, 3m and 5m – so you can match the exact cable run needed between instruments, antennas and mounting points without excess slack or signal-robbing extensions.
Technical Specifications
| Specification | Details |
| Connector A | SMA Male |
| Connector B | N-Type Male |
| Cable Type | Flexible RF Coaxial Cable Assembly |
| Impedance | 50 Ohm |
| Number of Conductors | 1 |
| Capacitance | 94 pF/m |
| Velocity of Propagation | 70% |
| Max Operating Frequency | 34 GHz (bare cable) / 18 GHz (with connectors) |
| Screening Effectiveness | >90dB |
| Dielectric Withstanding Voltage | 1500V @ DC |
| Phase Change vs. Bending | ±0.3°/GHz |
| Repeated Bending Radius | 1.575in (40mm) |
| Cable Weight | 0.041 kg/m |
| Operating Temperature | -55°C to +125°C |
| Available Lengths | 0.1m – 5m (10 options) |
| Condition | New |
Applications of This RF Coaxial Cable Assembly
RF and Microwave Test Laboratories
Connects vector network analysers, spectrum analysers and signal generators to devices under test, where stable impedance and low reflection are essential for accurate readings.
Antenna and GNSS/GPS Systems
The N-type end matches most antenna and GNSS/GPS receiver connectors, making this cable a practical bridge between SMA-based instruments and N-type antenna hardware used in survey, mapping and positioning equipment.
Telecommunications and Microwave Systems
Suitable for connecting RF amplifiers, microwave transmitters, base station components and satellite communication hardware that mix SMA and N-type interfaces.
Field Survey and Test Equipment
The flexible jacket and wide temperature rating make this cable practical for outdoor field work, mobile test rigs and equipment transported between sites.
Build Quality and Materials
- Silver-plated copper inner conductor for low resistance and excellent conductivity
- Solid PTFE dielectric insulation for stable impedance across temperature
- Silver-plated copper strip inner shield plus silver-plated copper wire outer braid for >90dB screening
- Flexible outer jacket rated from -55°C to +125°C
- Precision SMA male and N male connectors for secure, repeatable connections
Related and Complementary Products
Building a complete RF or antenna setup? See these related products:
- 18GHz SS402 SMA Male to SMA Male RF Test Cable the matching same-family cable with SMA connectors on both ends
- AG-35H GNSS Survey Antenna (TNC-SMA) a full-band GNSS antenna for pairing with SMA-based receivers
- VHF Marine Antenna with Coaxial Cable N-type compatible marine antenna and cable kit
- Magnetic Mount Coaxial Cable Antenna (UHF) magnetic-base antenna cable for vehicle-mounted RF setups
- 86917 ADL Pole Mount Antenna Cable TNC-to-NMO cable for radio-to-antenna connections in the field
Frequently Asked Questions
What frequency range does this SMA to N RF coaxial cable support?
This cable assembly supports signal transmission up to 18 GHz with the SMA and N-type connectors fitted, and up to 34 GHz on the bare coaxial cable, making it suitable for RF and microwave test applications.
What is the impedance and shielding performance of this cable assembly?
The cable maintains a standard 50-ohm impedance with screening effectiveness greater than 90dB, giving stable RF performance and strong resistance to external interference.
What is the difference between the SMA and N-type connector ends?
The SMA male end is a compact threaded connector commonly used on RF test instruments and PCB-mounted modules, while the N-type male end is a larger, weather-resistant threaded connector widely used on antennas, base stations and outdoor RF equipment. This assembly connects the two interfaces on a single low-loss cable run.
Can I order this cable in a custom length or connector configuration?
This listing covers 10 standard lengths from 0.1m to 5m. For custom lengths or alternative connector configurations, please contact us with your requirements before ordering.
Is this coaxial cable suitable for outdoor or field use?
Yes. The cable operates across a -55°C to +125°C temperature range with a durable, flexible jacket, making it suitable for outdoor field work, survey equipment and mobile test setups as well as indoor lab environments.
Is this a new, genuine cable assembly?
Yes. Every cable assembly is supplied brand new and tested for VSWR and insertion loss before dispatch.





Reviews
There are no reviews yet.